A microcontroller (or MCU) is a computer-on-a-chip. It is a type of microprocessor emphasizing self-sufficiency and cost-effectiveness, in contrast to a general-purpose microprocessor (the kind used in a PC).
The majority of computer systems in use today are embedded in other machinery, such as telephones, clocks, appliances, vehicles, and infrastructure. An embedded system usually has minimal requirements for memory and program length and may require simple but unusual input/output systems. For example, most embedded systems lack keyboards, screens, disks, printers, or other recognizable I/O devices of a personal computer. They may control electric motors, relays or voltages, and read switches, variable resistors or other electronic devices. Often, the only I/O device readable by a human is a single light-emitting diode, and severe cost or power constraints can even eliminate that.
In contrast to general-purpose CPUs, microcontrollers do not have an address bus or a data bus, because they integrate all the RAM and non-volatile memory on the same chip as the CPU. Because they need fewer pins, the chip can be placed in a much smaller, cheaper package.
Integrating the memory and other peripherals on a single chip and testing them as a unit increases the cost of that chip, but often results in decreased net cost of the embedded system as a whole. (Even if the cost of a CPU that has integrated peripherals is slightly more than the cost of a CPU + external peripherals, having fewer chips typically allows a smaller and cheaper circuit board, and reduces the labor required to assemble and test the circuit board). This trend leads to design.
A microcontroller is a single integrated circuit, commonly with the following features:
- central processing unit - ranging from small and simple 4-bit processors to sophisticated 32- or 64-bit processors
- input/output interfaces such as serial ports (UARTs)
- other serial communications interfaces like I²C, Serial Peripheral Interface and Controller Area Network for system interconnect
- peripherals such as timers and watchdog
- RAM for data storage
- ROM, EPROM, EEPROM or Flash memory for program storage
- clock generator - often an oscillator for a quartz timing crystal, resonator or RC circuit
- many include analog-to-digital converters
This integration drastically reduces the number of chips and the amount of wiring and PCB space that would be needed to produce equivalent systems using separate chips and have proved to be highly popular in embedded systems since their introduction in the 1970s.
Some microcontrollers can afford to use a Harvard architecture: separate memory buses for instructions and data, allowing accesses to take place concurrently.
The decision of which peripheral to integrate is often difficult. The Microcontroller vendors often trade operating frequencies and system design flexibility against time-to-market requirements from their customers and overall lower system cost. Manufacturers have to balance the need to minimize the chip size against additional functionality.
Microcontroller architectures are available from many different vendors in so many varieties that each instruction set architecture could rightly belong to a category of their own. Chief among these are the 8051, Z80 and ARM derivatives
Microcontrollers take the largest share of sales in the wider microprocessor market. Over 50% are "simple" controllers, and another 20% are more specialized digital signal processors (DSPs)[citation needed]. A typical home in a developed country is likely to have only one or two general-purpose microprocessors but somewhere between one and two dozen microcontrollers. A typical mid range automobile has as many as 50 or more microcontrollers. They can also be found in almost any electrical device: washing machines, microwave ovens, telephones etc.
Manufacturers have often produced special versions of their microcontrollers in order to help the hardware and software development of the target system. These have included EPROM versions that have a "window" on the top of the device through which program memory can be erased by ultra violet light, ready for reprogramming after a programming ("burn") and test cycle. Other versions may be available where the ROM is accessed as an external device rather than as internal memory. A simple EPROM programmer, rather than a more complex and expensive microcontroller programmer, may then be used, however there is a potential loss of functionality through pin outs being tied up with external memory addressing rather than for general input/output. These kind of devices usually carry a cost up in part prices but if the target production quantities are small, certainly in the case of a hobbyist, they can be the most economical option compared with the set up charges involved in mask programmed devices. A more rarely encountered development microcontroller is the "piggy back" version. This device has no internal ROM memory; instead pin outs on the top of the microcontroller form a socket into which a standard EPROM program memory device may be installed. The benefit of this approach is the release of microcontroller pins for input and output use rather than program memory. These kinds of devices are normally expensive and are impractical for anything but the development phase of a project.
Originally, microcontrollers were only programmed in assembly language, or later in C code. Recent microcontrollers integrated with on-chip debug circuitry accessed by In-circuit emulator via JTAG enables a programmer to debug the software of an embedded system with a debugger.
Some microcontrollers have begun to include a built-in high-level programming language interpreter for greater ease of use. The Intel 8052 and Zilog Z8 were available with BASIC very early on, and BASIC is more recently used in the popular BASIC Stamp MCUs.
Some microcontrollers such as Analog Device's Blackfin processors can be programmed using LabVIEW, which is a high level programming language, but some people's like writer use ProVIEW which is a C++ programming language and have simulator software included.
in contrast to general-purpose computers, microcontollers used in embedded systems often seek to minimize interrupt latency over instruction throughput and it has 4 interupt level priority.
When an electronic device causes an interrupt, the intermediate results, the registers, have to be saved before the software responsible for handling the interrupt can run, and then must be put back after it is finished. If there are more registers, this saving and restoring process takes more time, increasing the latency.
Low-latency CPUs generally have relatively few registers in their central processing units, or they have "shadow registers" that are only used by the interrupt software.
In advance microcontroller, it has power down function to make more efficient power comsumtion (edited from wikipedia)
No comments:
Post a Comment